In this video we talk about not exceeding 5mph during a recovery, and using the least amount of momentum necessary to free the stuck vehicle. "You can only go too fast once"

We pair the rope to the recovery vehicle. If the stuck vehicle is small, then reduce your momentum. If it is large, then full pulls, but not esceeding 5mph. When pairing the rope to the recovery vehicle, make sure that it futs within the working load limit of the rope. 

When connecting to a car, connect to the mfg recommended recovery points. One of those is not a screw in tow hook in the bumper of most cars and SUVs. Those are not meant for being yanked on, they are typically tac welded and can pop out with very minimal effort. 

There are many things to note when connecting to a hitch. Casey explains very well many things to consider. Never loop your rope over a ball on the end of the hitch and never do it on a drop hitch either. If you are using a pin, consider the sheer strength of the pin is now less than it would be if there was a square tube slid into the hitch. Also, never try to perform a recovery using the chain hook holes on the side of the hitch. They will damage the rope and are often very thin metal. 

Casey walks through important things to note when getting his equipment ready and also the person in the stuck vehicle. Always make sure there are no knots, or damage to the rope. Let the driver know to put it in drive and help a small amount. The recovery vehicle should be doing most of the work. If the driver of the stuck vehicle is spinning the tires, it causes the vehicle to sink, making it hard for the recovery vehicle to pull them up on top of the surface, rather than through it.

The driver of the stuck vehicle should put it in park. Inspect the rope and make sure there is no damage that occured during the recovery.

After 5 immediate pulls, the rope fibers are warm and stretched. The rope becomes more like a strap. It is recommended to wait 5 minutes for the rope to cool down and release the stretch that was in it and then proceed with more pulls. Something to note, if after two full pulls, if the vehicle doesn't move an inch, rethink your strategy or even if using a kinetic rope is the right thing to help the stuck vehicle. You may need to get out your shovel. 

When pulling at an angle, both vehicles will want to straighten out. This can force the vehicle to quickly try to slide to one side. If it catches traction, the vehicle can flip on to its side. Also, if the recovery vehicle gets pulled straight, it could then be pointed in a direction the driver is not wanting to go.

You can perform a recovery in reverse. However, you never want to turn your wheels if you are in 4wd. It can be very hard on your ring and pinion and break your 4wd. If possible, always perform a recovery driving forward.

Spreading the load  puts less strain on recovery points, as well as helping the vehicle being recovered to drive straight without being pulled to one side or the other.

You can double a rope back but it drastically reduces the stretch in the rope. This means, you most likely will want to act like you have a stiff strap, instead of a rope that stretches. A running start could then break parts if you have doubled it back. If it is a true basket, it will double the breaking strength of the rope, however when it is used as a bridle, the rope is not in a true "basket" and the angle of the rope will effect the breaking strength. Many bridles will list different angles and their mbs depending on the angle. If you use a rope that wasn't tested as a bridle, you may be guessing on the mbs. 

MBS is the minimum weight it takes to break a rope. That number is taken from breaking 10 ropes, and selecting the rope with the lowest weight it took to break it.  The WLL is the working load limit. That number is typically chosen using a safety factor. A safety factor is typically 3:1 or 5:1. The vehicle best suited for the rope is the MBS divided by 5, and also divided by 3 and that gives a safe range for the vehicle performing the recovery. I.e. a rope with an MBS of 30k lbs, has a safe WLL between 5k-10k lbs.  

An abrasion sleeve is best used close to the the stuck vehicle. In case the rope is rubbing on the underside of the vehicle, as well as against a tire when the vehicle is freed. It helps protect a rope, but cannot protect against very sharp edges or if it is smashed under a tire on a hard surface while a tire is spinning. 

A hard shackle is best used on a recovery point with hard, sharp metal edges. It is not recommended to ever use them to connect two ropes, in case of a failure. Soft shackles are very strong and are more gentle on the recovery points. 

Use a soft shackle to connect two ropes. Know that the kinetic energy can increase signifcantly. A double loop soft shackle is the best shackle to use when connecting two kinetic ropes. Never use a hard shackle to connect two kinetic ropes, it can become a projectile if there is a failure.